· IKSUN
Wave, S-Fold and Ripple Fold Curtains: Specify the Track Before the Heading
Three names — wave, S-fold and ripple fold — describe one visual idea: a curtain that hangs in a continuous run of even, S-shaped folds. The names do not describe one product. The carrier spacing, the heading tape and the track hardware differ between the systems, and a panel made for one track will not hang correctly on another.
One look, three names, different hardware
Start by matching the name your client uses to the hardware it implies. The values below are the commonly specified ones, not universal standards; confirm the exact spacing and tape width with the supplier before production, because practice varies between regions and manufacturers.
| Heading name | Where the name is used | Hardware as commonly specified |
|---|---|---|
| Wave / S-fold | United Kingdom, Europe, Australia | Dedicated wave track with corded gliders; heading tape with pockets at roughly 60 mm or 80 mm intervals |
| Ripple fold | North America | Dedicated snap-carrier track; snap-tape heading at roughly 125 mm tape width with carriers at roughly 80 mm spacing |
| Wave top | Various | Nylon tape sewn to the fabric; hangs on a standard track or rod without carriers; no heat setting |
Why the systems are not interchangeable
The even wave exists only because the hardware holds every attachment point at a fixed interval. A ripple fold panel carries snap tape at one spacing; an S-fold panel is sewn for a tighter carrier interval and different clip geometry. Swapped, the panel either will not attach or will hang with shallow, uneven folds — and the fault appears after installation, on site, in front of the client.
The practical rule: the heading is determined by the track, not the other way round. If a track is already installed — in a hotel room, a showroom or a completed residential floor — the heading is already decided. Measure the distance between two adjacent carriers, photograph the carrier itself, and send both with the enquiry.
Fullness, fabric and freight
Wave-family headings are specified by fullness ratio: the fabric width divided by the track length. Ratios between roughly 1.8x and 2.5x are common. A tighter wave interval produces a fuller look and uses more fabric; a wider one uses less and hangs lighter. The ratio also changes the stack: going from 2.0x to 2.2x deepens the open bundle, which matters where the stack has to clear a wall return or a sliding door.
The arithmetic is simple and worth writing into the order. Fabric width = track length × fullness. A 3 m track at 2.0x needs 6 m of fabric; at a 100 mm carrier interval that is roughly 60 carriers, plus master carriers and spares. Write the ratio and the interval as numbers, not as the trade name alone.
What the track specification must fix
Whether the track is hand-drawn or motorized, the same fields decide whether a wave heading will hang as intended. For a motorized run, add the drive: IKSUN quotes motorized bodies by mould number and drive family — Jialisi, Somfy or a universal belt-drive profile quoted without a motor — so the mould-number and kg/m profile table identifies the exact extrusion before the heading is discussed.
Where the track is recessed, the pocket is drawn before the ceiling is built, not after. A wave stack sits deeper than a flat-hung curtain at the same fullness, so the pocket section and the finished face belong on one drawing. The recessed built-in body is produced in two ceiling-pocket sections, 41.97 × 21.7 mm and 40 × 26 mm; state the section together with the plasterboard thickness and bracket arrangement, then check the ceiling pocket size guide.
The lines to put on the purchase order
Nine lines prevent almost every heading-versus-track dispute. Copy them into the enquiry:
| Order line | What to write |
|---|---|
| Heading name and system | Wave, S-fold, ripple fold or wave top — and the trade name your client used |
| Carrier or pocket spacing | In millimetres, measured between adjacent attachment points |
| Fullness ratio | For example 1.8x, 2.0x, 2.2x |
| Track length and mounting | Ceiling or wall, and the substrate: concrete, timber or drywall |
| Control method | Hand-drawn, cord-drawn or motorized, with the motor side if motorized |
| Whether the track is included | Curtains only, or curtains and hardware on one order |
| Runner and accessory count | Runners, master carriers, brackets, end covers, connectors |
| Fabric weight | Heavier blackout fabric needs closer bracket spacing and a stronger profile |
| Spare parts | Spare runners and brackets for project maintenance |
Heat setting is a process, not a discount
Wave-family panels need their fold memory set. In the usual process the finished panel is held at the correct carrier interval and exposed to controlled heat, so the fabric returns to its wave after being compressed for shipping and packing. A quotation that leaves this step out is not a discount. Ask each supplier how the folds are set, and what the panel looks like when it comes out of the carton.
What to send for a wave-ready track quotation
A quotation needs the heading system, the carrier spacing in millimetres, the fullness ratio, the track length and the destination country. Send the enquiry as one document with the ceiling condition and the mounting detail, so the quotation, the curtain track quotation checklist and the curtain track purchase specification all refer to the same configuration. IKSUN quotations are handled by one sales team at bbsyiyi@gmail.com or on WhatsApp +86 180 3323 8456.
FAQ
Can S-fold curtains hang on a ripple fold track?
No. The carrier spacing and clip geometry differ between the systems, so the panel will either not attach or will hang with shallow, uneven waves. Confirm the carrier spacing of the installed track before ordering the heading.
Do wave curtains need a special track?
Yes. The even wave is held by gliders or carriers fixed at a regular interval on a dedicated track. On a standard rod the folds collapse into an uneven gather.
How many carriers do I need per metre?
Work from fabric width, not track length: track length × fullness, divided by the carrier interval. Add master carriers and spares, and have the count confirmed against the ordered configuration.
Which heading should a hotel project specify?
Start from the hardware the property already runs. Wave-family headings stack neatly and stay even under daily cycling, but the installed track decides the heading, not the look.
Can I order the track without the curtains?
Yes. IKSUN quotes the track body, carriers, brackets and accessories as one scope. If the curtains are made elsewhere, send the heading system and the carrier spacing so the track is quoted to match.
What exactly is the carrier spacing measurement?
The distance between the attachment points of two adjacent carriers, measured centre to centre, plus a photograph of the carrier. Both go with the enquiry.
Send your wave heading requirements to IKSUN with the heading system, carrier spacing and track lengths you want confirmed.