IKSUNCurtain Hardware

Buyer guide

How to Measure for a Motorized Curtain Track | IKSUN

A motorized curtain track is cut to the project's own dimension, so the measurement you send decides the length, the motor clearance and the bracket spacing the factory builds. Measure the window width, add the curtain overlap, then note where the motor and brackets sit - IKSUN cuts every body to that dimension and quotes freight from the published mass per metre.

Catalogue imagery

Product photographs & profile drawings

Photographs and cross-section drawings reproduced from the IKSUN product catalogues. These images come from the IKSUN Excel product catalogues; no model number, rating or certification is asserted from a photograph alone. Browse the full image library.

IKSUN TS Special Aluminium Profiles - product photograph 0008 (from TS特殊铝轨(OK).xlsx)
TS Special Aluminium Profiles – product photograph. Source: TS特殊铝轨(OK).xlsx. View all TS Special Aluminium Profiles images
IKSUN TS Special Aluminium Profiles - product photograph 0026 (from TS特殊铝轨(OK).xlsx)
TS Special Aluminium Profiles – product photograph. Source: TS特殊铝轨(OK).xlsx. View all TS Special Aluminium Profiles images
IKSUN WG Bent / Curved Track - technical cross-section drawing 0062 (from WG弯轨(OK).xlsx)
WG Bent / Curved Track – technical cross-section drawing. Source: WG弯轨(OK).xlsx. View all WG Bent / Curved Track images

Side by side

At a glance

DimensionManual trackMotorized track
What you measureWindow width onlyWindow width, plus motor clearance and bracket zones
How it is setHung once, then fixedCut to the dimension you send, motor interface noted
Who cuts itBought at a standard off-the-shelf lengthFactory cuts to the project dimension you specify

The figures

The specification, in figures

Track length
Cut to the dimension you send
Curtain overlap
Added at the centre
Motor clearance
Noted at the end of the run
Bracket zones
Noted at both ends
Mass used for freight
0.315 - 1.13 kg/m
Reference bundle
6.7 m x 30 pieces

How to decide

What to weigh

Start with the window width

Measure the reveal from wall to wall at the top where the track sits, in millimetres. That span is the track length for a track that meets the two walls; a return to the ceiling adds the short return leg to the total.

Add the centre overlap

When two curtains meet in the middle they need roughly 150-300 mm of overlap so light does not gap through. Add that overlap to the track length before sending the dimension, or the curtains will stop short of closing.

Leave room for the motor

A motorized body needs clearance at one end for the motor and its lead, and a bracket close to the motor to carry the load. Mark the motor end on the drawing so the factory cuts the body to the right overall length.

Heavier profiles need closer brackets

IKSUN publishes the theoretical mass per metre for all 38 bodies, from 0.315 kg/m to 1.13 kg/m. The belt, motor and curtain add to the working load a bracket carries, so a wider span or heavier curtain takes closer brackets - state the curtain weight with the length.

Key facts

The figures on this page, stated plainly

  • The current tooling list holds 38 motorized curtain track profiles, plus 4 additional dies for motor housings and accessories.

  • Of the 38 track bodies, 14 are produced for Jialisi drives, 8 for Somfy drives, and 16 are universal belt-drive profiles quoted without a motor.

  • IKSUN track bodies run from 0.315 to 1.13 kilograms per metre; the lightest is mould CS101 and the heaviest is mould CP83 / MZX-180.

Questions on this guide

Answers buyers ask

How do I measure the length for a motorized curtain track?

Measure the window reveal from wall to wall in millimetres at the track line, add any ceiling return, then add the centre curtain overlap (about 150-300 mm). Send that total length with the profile or mould number; IKSUN cuts the body to that dimension.

Do I need to add overlap when measuring curtain tracks?

Yes, for a centre-opening pair. The two curtains need roughly 150-300 mm of overlap where they meet, or a light gap stays open. Add the overlap to the track length before sending the dimension so the curtains close fully.

Get in touch

Specify your curtain track

Send the profile or mould number, length and quantity - IKSUN returns price, lead time and carton data with the quotation.