IKSUNCurtain Hardware

Buyer guide

Ceiling Pocket Size for Curtain Tracks | IKSUN

A recessed motorized curtain track needs its place in the ceiling decided before the ceiling is built, not during installation. This guide tells architects, builders and importers what pocket size to reserve so an IKSUN track - including the AT81 that also carries its light - drops into the soffit, and what ceiling load the pocket must carry.

Catalogue imagery

Product photographs & profile drawings

Photographs and cross-section drawings reproduced from the IKSUN product catalogues. These images come from the IKSUN Excel product catalogues; no model number, rating or certification is asserted from a photograph alone. Browse the full image library.

IKSUN TS Special Aluminium Profiles - technical cross-section drawing 0015 (from TS特殊铝轨(OK).xlsx)
TS Special Aluminium Profiles – technical cross-section drawing. Source: TS特殊铝轨(OK).xlsx. View all TS Special Aluminium Profiles images
IKSUN TS Special Aluminium Profiles - product photograph 0033 (from TS特殊铝轨(OK).xlsx)
TS Special Aluminium Profiles – product photograph. Source: TS特殊铝轨(OK).xlsx. View all TS Special Aluminium Profiles images
IKSUN WG Bent / Curved Track - technical cross-section drawing 0095 (from WG弯轨(OK).xlsx)
WG Bent / Curved Track – technical cross-section drawing. Source: WG弯轨(OK).xlsx. View all WG Bent / Curved Track images

The figures

The specification, in figures

Recessed pocket section 1
41.97 x 21.7 mm
Recessed pocket section 2
40 x 26 mm
AT81 rail wall
2.0 mm
WR510 square section
31.1 x 22.5 mm
Track body mass range
0.315 - 1.13 kg/m
Motor interfaces
Somfy, Jialisi

How to decide

What to weigh

Two pocket sections to match

The IKSUN recessed built-in body is produced in two ceiling-pocket sections, 41.97 x 21.7 mm and 40 x 26 mm, so the pocket an architect draws can be matched to the track rather than re-cut on site.

Reserve the pocket before the ceiling closes

A recessed track only fits if the pocket is on the drawing first. Because the body is made for those two sections, the ceiling detail has to be fixed before the soffit is built, not discovered during fitting.

Integrated light shares the same box

Where the AT81 is specified, the COB light strip sits inside the same extrusion as the belt drive, so the curtain box carries both the motor and the light with no separate lighting channel to reserve.

The square lit track is slim

The WR510 is a 31.1 x 22.5 mm square track with a downward-facing LED channel, so a lit run needs only a shallow slot rather than a full lighting pelmet above the window.

Mind the ceiling load

IKSUN track bodies run from 0.315 to 1.13 kg per metre across 38 profiles, so the pocket and its brackets must carry the chosen profile's mass plus the motor and any light, and that mass is published per profile before the quote.

Motor is reached from the pocket

The recessed body is produced in Somfy and Jialisi motor interfaces on the same extrusion, so the motor is serviced from the ceiling pocket rather than from below the room.

Key facts

The figures on this page, stated plainly

  • The IKSUN recessed built-in track is produced in two ceiling-pocket sections, 41.97 x 21.7 mm and 40 x 26 mm, so it can match a pocket already drawn by a project architect.

  • The AT81 carries its COB light strip inside the same extrusion as the belt drive, so the curtain box needs no separate lighting channel, and the strip has no polarity to observe when fitting.

  • The IKSUN WR510 is a 31.1 x 22.5 mm square curtain track with a downward-facing LED channel, so the light falls on the curtain rather than across the ceiling.

  • IKSUN track bodies run from 0.315 to 1.13 kilograms per metre; the lightest is mould CS101 and the heaviest is mould CP83 / MZX-180.

  • Belt-drive system. Confirm the supplied motor model, input voltage, rated curtain load and controller compatibility before ordering.

Questions on this guide

Answers buyers ask

What ceiling pocket size do I need for a recessed motorized curtain track?

The IKSUN recessed built-in body is produced in two ceiling-pocket sections, 41.97 x 21.7 mm and 40 x 26 mm. Reserve the matching pocket in the drawing before the soffit is built; if neither pocket exists, a surface track is the faster route because it clips to the finished ceiling.

Does the AT81 need extra space in the curtain box for its light?

No. The AT81 carries its COB light strip inside the same extrusion as the belt drive, so the curtain box needs no separate lighting channel - the motor and the light share one body. Reserve the pocket for the AT81's ceiling-mounted section and its 2.0 mm rail wall.

How much space does a lit square track need?

The WR510 is a 31.1 x 22.5 mm square track with a downward-facing LED channel, so a lit run needs only a shallow slot rather than a full lighting pelmet; the light falls on the curtain, not across the ceiling.

What ceiling load must the pocket support?

IKSUN track bodies run from 0.315 to 1.13 kg per metre across 38 profiles, and the chosen profile's mass is published per metre, so the pocket and its brackets must carry that plus the motor and any light; quote the profile or mould number to confirm the load for the section.

Get in touch

Specify your curtain track

Send the profile or mould number, length and quantity - IKSUN returns price, lead time and carton data with the quotation.