IKSUNCurtain Hardware

Buyer guide

Telescopic Motorized Curtain Track - IKSUN

A telescopic track is the one motorized body in the range that does not arrive at a fixed length. Two aluminium tubes slide into one another - an inner tube and an outer tube - so the finished run is set on site rather than on the drawing. Two of the 38 bodies on the tooling are built this way, and they are what a buyer specifies when the opening is uncertain, the window is not straight, or the same track has to fit more than one room.

Catalogue imagery

Product photographs & profile drawings

Photographs and cross-section drawings reproduced from the IKSUN product catalogues. These images come from the IKSUN Excel product catalogues; no model number, rating or certification is asserted from a photograph alone. Browse the full image library.

IKSUN LM Roman Curtain Track - technical cross-section drawing 0052 (from LM罗马轨(OK).xlsx)
LM Roman Curtain Track – technical cross-section drawing. Source: LM罗马轨(OK).xlsx. View all LM Roman Curtain Track images
IKSUN LM Roman Curtain Track - technical cross-section drawing 0018 (from LM罗马轨(OK).xlsx)
LM Roman Curtain Track – technical cross-section drawing. Source: LM罗马轨(OK).xlsx. View all LM Roman Curtain Track images
IKSUN H Curtain Rings / Sliders - product photograph 0012 (from H滑环(OK).xlsx)
H Curtain Rings / Sliders – product photograph. Source: H滑环(OK).xlsx. View all H Curtain Rings / Sliders images

Side by side

At a glance

DimensionOn the toolingWhat it means on site
Inner tubeDD18 - WR561 - 0.466 kg/mThe smaller section; it slides inside the outer tube
Outer tubeDD19 - WR383 - 0.515 kg/mThe larger section; it receives the inner tube
DriveBelt drive, motor supplied to orderSame belt drive as the rest of the range, so the motor is chosen separately
Bodies in the range2 of the 38Both are quoted by mould number, like every other body
Cut lengthNot fixed at 6.7 mThe run is set by extending or drawing the tubes on site
Parts that scaleSliding beads and top codesCounted from the finished length once it is set
Drive beltOne continuous runFitted to the length the tubes end up at
DeliveryQuoted by mould number and quantityThe factory needs the quantity before it issues the quotation

How to decide

What to weigh

Two bodies make one telescopic track

A telescopic run is a pair, not a length: the DD18 inner tube slides into the DD19 outer tube. Neither body is a complete track on its own, so both mould numbers go on the order. Their published masses are 0.466 and 0.515 kg per metre, which is what the freight and the ceiling load are calculated from.

The belt-drive body takes a motor separately

Both telescopic bodies are general belt-drive profiles. Of the 38 bodies in the range, 16 are supplied without a motor, and a telescopic pair is among them. The motor is therefore a separate line on the order rather than something already in the box - which is what makes the pair useful to a buyer who already stocks one motor across a project.

The finished length is set on site, not on the order

Every other body in the range is cut to the room dimension and quoted at that length. A telescopic body is not: the run is extended or drawn out when it is installed, so the length the drawing shows is a target rather than a cut size. Send the drawing with the tolerance you need the run to hold, and say which of the two bodies the order is for.

The parts that scale are counted after the length is set

Sliding beads and top codes scale with the track - the AT81 packing list counts 8 beads and 2 codes per metre - and the drive belt is fitted as one continuous run. On a telescopic body all three follow the length the tubes end up at, so the accessory count is settled on site rather than on the order.

What a telescopic body is not for

It is not a curved track. A bay window or a corner opening needs a body that bends, and the tooling catalogue records telescopic and splice bodies as separate entries - there is no bendable body on the current tooling. A telescopic run solves an uncertain or repeated length; it does not solve a shape.

Splices are the other answer to a long run

Where a run is longer than one length, the range also carries splice bodies - the DD31 outer connector and the DD32 splice track - and the standard bill of materials issues one internal splice strip per joint. A splice fixes a length permanently; a telescopic body leaves it adjustable. Which one the opening needs is a drawing decision.

Both are quoted by mould number

As with every other body in the range, the quotation is written against the mould number - WR561 and WR383 for the telescopic pair - and the accessory list travels with it. A replacement order for a different room is the same two numbers and a quantity, not a guess from a photograph.

Key facts

The figures on this page, stated plainly

  • The current tooling list holds 38 motorized curtain track profiles, plus 4 additional dies for motor housings and accessories.

  • Of the 38 track bodies, 14 are produced for Jialisi drives, 8 for Somfy drives, and 16 are universal belt-drive profiles quoted without a motor.

  • Every IKSUN track body is quoted by its mould number, which is the die identification the factory uses, together with its theoretical mass per metre for freight calculation.

Questions on this guide

Answers buyers ask

What is a telescopic motorized curtain track?

A track whose length is adjustable instead of fixed. It is made of two aluminium bodies - the DD18 inner tube and the DD19 outer tube - that slide into one another, so the finished run is set when it is installed rather than when it is cut. Both are general belt-drive profiles on the current tooling, at 0.466 and 0.515 kg per metre.

How long is a telescopic curtain track when it arrives?

The track is not cut to one length. The two tubes are supplied as bodies, and the run is extended or drawn out on site to the opening. That is the point of the product. Send the drawing, the tolerance the finished run must hold, and the quantity. We quote against the two mould numbers, with the motor as a separate line.

When should I specify a telescopic track rather than a cut track?

When the opening is uncertain, when the same track has to fit more than one room, or when the finished length is not known until the site is measured. If the run is longer than one length and the length is fixed, the splice bodies are the answer instead - and if the opening bends, neither is, because there is no bendable body on the current tooling.

Get in touch

Specify your curtain track

Send the profile or mould number, length and quantity - IKSUN returns price, lead time and carton data with the quotation.