Buyer guide
Curtain Track Accessories and Spares | IKSUN
A motorized curtain track is not one extrusion. It is a profile, a drive, and a set of parts that have to arrive together and go up together - and a buyer who is quoted the profile alone has been quoted half the order. IKSUN publishes the standard bill of materials for the range, so you can see what is in the box, what is counted per metre, and what your drawing decides.
Side by side
At a glance
| Dimension | In the box | How it is scaled |
|---|---|---|
| Motor and remote controller | One of each per motorised run | Fixed - it does not scale with the track length |
| Transmission boxes | One pair per run | Fixed |
| Sliding trolleys (carriers) | One pair per run | Fixed |
| Sliding beads | 8 per metre on the AT81 packing list | Counted from the finished cut length |
| Top codes | 2 per metre on the AT81 packing list | Counted from the finished cut length |
| Drive belt | One continuous run | The length of the whole track, not a piece per metre |
| Hooks and end locks | Two of each, stainless steel or plastic | Fixed |
| Ceiling and second-layer brackets | Supplied with the run | How many is set by your drawing |
| Internal splice strip | One per joint | Only when two lengths are joined |
Factory photographs
The parts, photographed in the factory
These are the parts from the factory's own accessory catalogue, photographed for this page. The code under each photograph is the catalogue item number, so a replacement order can name the part instead of describing it. The six groups below are the transmission boxes, the sliding carriers, the drive belt, the hardware that goes with them, the motors and the remote controllers.
Drive transmission

DD201 
DD202 
DD203 
DD204 
DD205 
DD209 
DD314 
DD315 
DD321 
DD323 
DD324 
DD334 
DD347 
DD348
Sliding carrier

DD222 
DD232 
DD257 
DD280 
DD289 
DD299 
DD300 
DD311 
DD349
Drive belt

DD230 
DD269 
DD277 
DD296 
DD336
Fitting and hardware

DD223 
DD224 
DD225 
DD226 
DD227 
DD228 
DD229 
DD234 
DD241 
DD242 
DD243 
DD258 
DD264 
DD265 
DD273 
DD287 
DD288 
DD293 
DD294 
DD295 
DD297 
DD298 
DD346
Motor

DD218 
DD219 
DD233 
DD238 
DD239 
DD249 
DD250 
DD251 
DD253 
DD254 
DD255 
DD256 
DD310 
DD309 
DD337 
DD338 
DD339 
DD340 
DD345 
DD313
Remote controller

DD210 
DD211 
DD212 
DD213 
DD214 
DD247 
DD248 
DD308 
DD301 
DD341 
DD342 
DD351
The motor and the remote controller are quoted against the motor interface you specify, so quote the item code together with the interface rather than the code on its own.
How to decide
What to weigh
The drive on the body decides which motor you order
Of the 38 track bodies in the range, 14 are made for Jialisi motors, 8 are made for Somfy motors, and 16 are general belt-drive profiles supplied without a motor. The profile number therefore fixes the drive end: quote the mould number and the motor interface, and the accessory list follows from them.
The belt is one run, not a piece per metre
The standard bill of materials lists the drive belt as a single run the length of the track. A track made from two lengths still needs one continuous belt and one internal splice strip, which is why the factory needs the finished length before it cuts rather than the rough opening.
Beads and codes are counted from the cut length
Sliding beads and top codes are the two parts that scale with the track. The AT81 packing list counts 8 sliding beads and 2 top codes per metre, so a 12 metre run carries 96 beads and 24 codes. Each product states its own per-metre count in its packing list.
Brackets are the part your drawing decides
Ceiling brackets and second-layer brackets come with the run, but how many is a drawing decision, not a catalogue number. The count follows the spacing and the ceiling build-up, and the motor end needs clearance marked on the drawing before the body is cut.
Everything is quoted against the mould number
A track body is quoted by its mould number, which is the tooling identifier the factory uses. The accessory list travels with that number, so a replacement order is a mould number and a length rather than a guess from a photograph.
Key facts
The figures on this page, stated plainly
The current tooling list holds 38 motorized curtain track profiles, plus 4 additional dies for motor housings and accessories.
Of the 38 track bodies, 14 are produced for Jialisi drives, 8 for Somfy drives, and 16 are universal belt-drive profiles quoted without a motor.
Every IKSUN track body is quoted by its mould number, which is the die identification the factory uses, together with its theoretical mass per metre for freight calculation.
Questions on this guide
Answers buyers ask
What is included with a motorized curtain track?
The standard bill of materials for the range is one motor, one remote controller, one pair of transmission boxes, one pair of sliding trolleys, one internal splice strip, two stainless steel or plastic hooks, two stainless steel end locks, ceiling and second-layer brackets, sliding beads to the length of the track, and the drive belt as a single run. It is the same list for every belt-drive body, with the per-metre counts taken from the packing list of the profile you quote.
How many sliding beads and top codes do I need?
They are counted per metre from the finished cut length, and the AT81 packing list states 8 sliding beads and 2 top codes per metre, so a 12 metre run carries 96 beads and 24 codes. Send the length the track is cut to rather than the rough opening, and each product's own packing list gives the count for that profile.
Does the motor come with the track?
It depends on the profile. Of the 38 track bodies, 14 are made for Jialisi motors, 8 for Somfy motors, and 16 are general belt-drive profiles supplied without a motor, so the mould number decides whether the motor is part of the order or something you add to it.
Related pages
Keep reading
Get in touch
Specify your curtain track
Send the profile or mould number, length and quantity - IKSUN returns price, lead time and carton data with the quotation.