· IKSUN
Recessed vs Surface-Mounted Motorized Curtain Tracks: Which Fits Your Ceiling?
A recessed motorized curtain track and a surface-mounted one run on the same belt-drive bodies and accept the same motor interfaces. What separates them is the ceiling: one needs a pocket drawn before the plasterboard closes, the other clips to a finished soffit. Decide that first and the rest of the specification follows.
The short answer
Where the architect has drawn a ceiling pocket, specify the recessed built-in body and the track disappears when the curtain is drawn back. Where the ceiling is already finished, a surface track is the faster route: it clips below the ceiling and needs no structural change. Neither choice changes the motor interface.
What recessed really means
The IKSUN recessed built-in body is made in two ceiling-pocket sections, 41.97 x 21.7 mm and 40 x 26 mm, so a pocket already on the drawing can be matched instead of rebuilt. The body sits inside a plasterboard pocket and is invisible when the curtain is open; the pocket drawing has to be agreed before the track is fitted. See the ceiling pocket size guide for the two sections.
Each body is supplied in a Somfy or a Jialisi motor interface on the same concealed profile, so a distributor can hold one track body across projects that name different motor brands. The extrusion is 6063-T5 aluminium with an electrophoretic finish; WR485 and WR486 are published at 0.437-0.446 kg per metre. Silent carriers with wear-resistant wheels are specified because the track runs close to the ceiling surface, where running noise is the common complaint on recessed installations.
What surface-mounted really means
A surface track clips to a finished ceiling on brackets. It needs no pocket and no structural change, which makes it the faster route for a retrofit, a refurbishment or a ceiling that is already closed. The same belt-drive bodies are used, so the profile, length and motor choice are unchanged.
Across the IKSUN range the track bodies run from 0.315 to 1.13 kg per metre; the lightest is mould CS101 and the heaviest is mould CP83 / MZX-180. A short domestic span takes a light profile; a wide span needs a heavier body and closer brackets. Every profile publishes its mass per metre, so ceiling load and freight can be checked before the price arrives.
Side by side: eight decision points
| Decision point | Recessed built-in | Surface-mounted |
|---|---|---|
| Ceiling condition | Pocket drawn before the plasterboard closes | Clips to a finished ceiling, no structural change |
| Visibility when open | Concealed inside the ceiling pocket | Track stays visible below the ceiling |
| Installation order | Pocket built first, agreed at drawing stage | Fitted after other trades have left |
| Body section | 41.97 x 21.7 mm or 40 x 26 mm pocket | No pocket required; same belt-drive bodies |
| Profile mass | 0.437-0.446 kg/m for WR485 and WR486 | 0.315-1.13 kg/m across the full range |
| Motor interface | Somfy or Jialisi | Somfy or Jialisi |
| Service access | Motor reached through the ceiling pocket | Motor reached from below the ceiling |
| Best fit | New-build hotels, villas, residential | Retrofit, refurbishment, finished ceilings |
Why the installation order decides the job
A recessed body has to be coordinated at drawing stage. The pocket is built first, the section is matched to the joinery detail, and the finish colour is fixed at order because the electrophoretic coating is applied to the full bundle. A late change means ceiling work, not just a different track.
A surface track can be fitted after other trades have left. Recessed, surface and wall mountings use the same belt-drive bodies and the same 6.7 m lengths; what changes is the fixing detail and where the motor is reached for service. A project can therefore switch mounting method late without re-specifying the track; the dimensions and installation guide sets out the sections and lengths.
What stays the same
The mounting choice does not open a second catalogue.
Both options run on the same belt-drive bodies, accept Somfy and Jialisi interfaces, and take 24-40 mm tubes on the carriers. A quote needs the profile or mould-number profile table, a quantity and a destination country. The ceiling pocket size guide fixes the pocket drawing and the section before the order.
| Decision point | Recessed built-in |
|---|---|
| Drives | Same belt-drive bodies as the surface and wall options |
| Motor interfaces | Somfy and Jialisi; 24-40 mm tubes fit the carriers |
| Standard length | 6.7 m cut length, joined at a splice on longer runs |
| Freight basis | Theoretical kg/m published per profile before a quote |
Choose by project type
Hotels, villas and new-build residential projects usually have a ceiling detail drawn in advance, so the recessed body can be written into the specification and the track disappears into the curtain box. Commercial fit-outs and refurbishments over an existing finished ceiling use the surface route: the track is visible, but the ceiling stays untouched and the programme is shorter. The comparison table above is the checklist for either decision.
Three fields buyers leave open
First, the pocket drawing. A recessed body is only useful if the 41.97 x 21.7 mm or 40 x 26 mm section matches the detail already drawn. Second, the load: kg per metre identifies the profile and supports material and freight calculations, but it is not a curtain load rating, which is confirmed for the installed configuration. Third, the motor: compatibility is stated for Somfy and Jialisi only and other brands need a sample test before ordering, as the motor compatibility guide states. The curtain track quotation checklist lists the fields a quotation should confirm.
FAQ
Which option is cheaper?
Ask for a quotation on a matched configuration. A recessed body adds the pocket detail to the ceiling package, while a surface track saves that structural work. IKSUN publishes the section and kg/m for every profile so the two can be compared on the same basis; the final price is confirmed on the quotation.
Does the mounting method change which motor I can use?
No. Recessed, surface and wall mountings run on the same belt-drive bodies with Somfy and Jialisi interfaces, and 24-40 mm tubes fit the carriers. Motor choice follows the belt load and the control system, not the way the track is fixed to the ceiling.
Can a recessed track be fitted to an existing finished ceiling?
Not without opening the ceiling. A recessed body requires the pocket to be built before the track is fitted and the pocket drawing must be agreed first. Where the ceiling is already finished, a surface track is the faster route.
What ceiling pocket does the recessed body need?
The IKSUN recessed built-in track is made in two pocket sections, 41.97 x 21.7 mm and 40 x 26 mm. Choose the one that matches the joinery detail already drawn by the project architect instead of rebuilding the ceiling.
Can the mounting method change after the order is placed?
All three mountings use the same belt-drive bodies and the same 6.7 m lengths, so a project can switch mounting method late without changing the track specification. Confirm the change with the supplier before production, because the fixing detail and bracket set are different.
Which option runs more quietly?
Recessed bodies are specified with silent carriers and wear-resistant wheels because the track sits close to the ceiling surface, where running noise is the main complaint on recessed installations. Ask for the carrier specification on the quotation for either option.
Is kg/m the curtain load rating?
No. It is the theoretical mass of the aluminium profile per metre and supports material and freight calculations. The permissible curtain load must be confirmed for the installed system, including span, bracket spacing, fixings and motor configuration.
Send your mounting question to IKSUN Distributors, importers: talk to us. with the ceiling condition, the pocket section or bracket detail, and the motor interface you want confirmed.